patch-2.3.26 linux/include/net/irda/uircc.h

Next file: linux/include/net/irda/wrapper.h
Previous file: linux/include/net/irda/smc-ircc.h
Back to the patch index
Back to the overall index

diff -u --recursive --new-file v2.3.25/linux/include/net/irda/uircc.h linux/include/net/irda/uircc.h
@@ -1,125 +0,0 @@
-/*********************************************************************
- *                
- * Filename:      uircc.h
- * Version:       0.1
- * Description:   Driver for the Sharp Universal Infrared 
- *                Communications Controller (UIRCC)
- * Status:        Experimental.
- * Author:        Dag Brattli <dagb@cs.uit.no>
- * Created at:    Sat Dec 26 11:00:49 1998
- * Modified at:   Thu Mar 11 01:37:20 1999
- * Modified by:   Dag Brattli <dagb@cs.uit.no>
- * 
- *     Copyright (c) 1998 Dag Brattli, All Rights Reserved.
- *      
- *     This program is free software; you can redistribute it and/or 
- *     modify it under the terms of the GNU General Public License as 
- *     published by the Free Software Foundation; either version 2 of 
- *     the License, or (at your option) any later version.
- *  
- *     Neither Dag Brattli nor University of Tromsų admit liability nor
- *     provide warranty for any of this software. This material is 
- *     provided "AS-IS" and at no charge.
- *     
- ********************************************************************/
-
-#ifndef UIRCC_H
-#define UIRCC_H
-
-/* Control registers (write only) */
-#define UIRCC_CR0           0x00 /* Control register 0 */
-#define UIRCC_CR0_XMIT_RST  0x20 /* Transmit reset */
-#define UIRCC_CR0_RECV_RST  0x10 /* Receive reset */
-#define UIRCC_CR0_TMR_RST   0x08 /* Timer reset */
-#define UIRCC_CR0_SYS_RST   0x04 /* System reset */
-#define UIRCC_CR0_CARR_RST  0x02 /* Carrier latch reset */
-#define UIRCC_CR0_CNT_SWT   0x01 /* Transmit/receive length counter reset */
-
-#define UIRCC_CR1           0x01 /* Transmit/receive mode setting register */
-#define UIRCC_CR1_RX_DMA    0x80 /* Rx DMA mode */
-#define UIRCC_CR1_TX_DMA    0x20 /* Tx DMA mode */
-#define UIRCC_CR1_DMA_BRST  0x10 /* DMA burst mode */
-#define UIRCC_CR1_MUST_SET  0x0c /* Must be set */
-
-#define UIRCC_CR2           0x02 /* Interrupt mask register */
-#define UIRCC_CR2_RECV_OVR  0x40 /* Receive overrun error */
-#define UIRCC_CR2_RECV_FRM  0x20 /* Receive frame error */
-#define UIRCC_CR2_RECV_END  0x10 /* Receive end */
-#define UIRCC_CR2_TMR_OUT   0x08 /* Timer time-out */
-#define UIRCC_CR2_XMIT_UNR  0x04 /* Transmit under-run error */
-#define UIRCC_CR2_XMIT_END  0x01 /* Transmit end */
-#define UIRCC_CR2_RECV_MASK 0x70
-#define UIRCC_CR2_XMIT_MASK 0x05
-
-#define UIRCC_CR3           0x03 /* Transmit/receive control */
-#define UIRCC_CR3_XMIT_EN   0x80 /* Transmit enable */
-#define UIRCC_CR3_TX_CRC_EN 0x40 /* Transmit UIRCC_CRC enable */
-#define UIRCC_CR3_RECV_EN   0x20 /* Receive enable */
-#define UIRCC_CR3_RX_CRC_EN 0x10 /* Receive CRC enable */
-#define UIRCC_CR3_ADDR_CMP  0x08 /* Address comparison enable */
-#define UIRCC_CR3_MCAST_EN  0x04 /* Multicast enable */
-
-#define UIRCC_CR4           0x04 /* Transmit data length low byte */
-#define UIRCC_CR5           0x05 /* Transmit data length high byte */
-#define UIRCC_CR6           0x06 /* Transmit data writing low byte */
-#define UIRCC_CR7           0x07 /* Transmit data writing high byte */
-
-#define UIRCC_CR8           0x08 /* Self pole address */
-
-#define UIRCC_CR9           0x09 /* System control 1 */
-
-#define UIRCC_CR10          0x0a /* Modem selection */
-#define UIRCC_CR10_SIR      0x22 /* Set SIR mode */
-#define UIRCC_CR10_FIR      0x88 /* Set FIR mode */
-
-#define UIRCC_CR11          0x0b /* System control 2 (same as SR11) */
-#define UIRCC_CR11_TMR_EN   0x08
-
-#define UIRCC_CR12          0x0c /* Timer counter initial value (low byte) */
-#define UIRCC_CR13          0x0d /* Timer counter initial value (high byte) */
-#define UIRCC_CR15          0x0f
-
-/* Status registers (read only) */
-#define UIRCC_SR0           0x00 /* Transmit/receive status register */
-#define UIRCC_SR0_RX_RDY    0x80 /* Received data ready */
-#define UIRCC_SR0_RX_OVR    0x40 /* Receive overrun error */
-#define UIRCC_SR0_RX_CRCFRM 0x20 /* Receive CRC or framing error */
-
-#define UIRCC_SR2           0x02 /* Interrupt mask status */
-
-#define UIRCC_SR3           0x03 /* Interrupt factor register */
-#define UIRCC_SR3_RX_OVR_ER 0x40 /* Receive overrun error */
-#define UIRCC_SR3_RX_FRM_ER 0x20 /* Receive frameing error */
-#define UIRCC_SR3_RX_EOF    0x10 /* Receive end of frame */
-#define UIRCC_SR3_TMR_OUT   0x08 /* Timer timeout */
-#define UIRCC_SR3_TXUR      0x04 /* Transmit underrun */
-#define UIRCC_SR3_TX_DONE   0x01 /* Transmit all sent */
-
-#define UIRCC_SR4           0x04 /* TX/RX data length counter low byte */
-#define UIRCC_SR5           0x05 /* TX/RX data length counter high byte */
-
-#define UIRCC_SR8           0x08 /* Chip version */
-
-#define UIRCC_SR9           0x09 /* System status 1 */
-
-#define UIRCC_SR10          0x0a /* Modem select status */
-#define UIRCC_SR11          0x0b
-#define UIRCC_SR12          0x0c /* Timer counter status (low byte) */
-#define UIRCC_SR13          0x0d /* Timer counter status (high byte) */
-#define UIRCC_SR15          0x0f
-
-#include <net/irda/irda_device.h>
-
-/* Private data for each instance */
-struct uircc_cb {
-	struct net_device idev;
-	
-	__u8 cr3;                 /* Copy of register sr3 */
-};
-
-#define CR3_SET
-
-#endif
-
-
-

FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)