patch-2.4.5 linux/arch/ppc/boot/mbx/m8xx_tty.c

Next file: linux/arch/ppc/boot/mbx/misc.c
Previous file: linux/arch/ppc/boot/mbx/m8260_tty.c
Back to the patch index
Back to the overall index

diff -u --recursive --new-file v2.4.4/linux/arch/ppc/boot/mbx/m8xx_tty.c linux/arch/ppc/boot/mbx/m8xx_tty.c
@@ -0,0 +1,288 @@
+/*
+ * BK Id: SCCS/s.m8xx_tty.c 1.8 05/18/01 07:54:04 patch
+ */
+
+
+/* Minimal serial functions needed to send messages out the serial
+ * port on the MBX console.
+ *
+ * The MBX uxes SMC1 for the serial port.  We reset the port and use
+ * only the first BD that EPPC-Bug set up as a character FIFO.
+ *
+ * Later versions (at least 1.4, maybe earlier) of the MBX EPPC-Bug
+ * use COM1 instead of SMC1 as the console port.  This kinda sucks
+ * for the rest of the kernel, so here we force the use of SMC1 again.
+ */
+#include <linux/config.h>
+#include <linux/types.h>
+#include <asm/uaccess.h>
+#include <asm/mpc8xx.h>
+#include "../../8xx_io/commproc.h"
+
+#ifdef CONFIG_MBX
+#define MBX_CSR1	((volatile u_char *)0xfa100000)
+#define CSR1_COMEN	(u_char)0x02
+#endif
+
+#ifdef TQM_SMC2_CONSOLE
+#define PROFF_CONS	PROFF_SMC2
+#define CPM_CR_CH_CONS	CPM_CR_CH_SMC2
+#define SMC_INDEX	1
+static volatile iop8xx_t *iopp = (iop8xx_t *)&(((immap_t *)IMAP_ADDR)->im_ioport);
+#else
+#define PROFF_CONS	PROFF_SMC1
+#define CPM_CR_CH_CONS	CPM_CR_CH_SMC1
+#define SMC_INDEX	0
+#endif
+
+static cpm8xx_t	*cpmp = (cpm8xx_t *)&(((immap_t *)IMAP_ADDR)->im_cpm);
+
+void
+serial_init(bd_t *bd)
+{
+	volatile smc_t		*sp;
+	volatile smc_uart_t	*up;
+	volatile cbd_t	*tbdf, *rbdf;
+	volatile cpm8xx_t	*cp;
+	uint	dpaddr, memaddr, ui;
+
+	cp = cpmp;
+	sp = (smc_t*)&(cp->cp_smc[SMC_INDEX]);
+	up = (smc_uart_t *)&cp->cp_dparam[PROFF_CONS];
+
+	/* Disable transmitter/receiver.
+	*/
+	sp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
+
+#ifdef CONFIG_FADS
+	/* Enable SMC1/2 transceivers.
+	*/
+	*((volatile uint *)BCSR1) &= ~(BCSR1_RS232EN_1|BCSR1_RS232EN_2);
+#endif
+
+#ifndef CONFIG_MBX
+	{
+	/* Initialize SMCx and use it for the console port.
+	 */
+
+	/* Enable SDMA.
+	*/
+	((immap_t *)IMAP_ADDR)->im_siu_conf.sc_sdcr = 1;
+
+#ifdef TQM_SMC2_CONSOLE
+	/* Use Port A for SMC2 instead of other functions.
+	*/
+	iopp->iop_papar |=  0x00c0;
+	iopp->iop_padir &= ~0x00c0;
+	iopp->iop_paodr &= ~0x00c0;
+#else
+	/* Use Port B for SMCs instead of other functions.
+	*/
+	cp->cp_pbpar |= 0x00000cc0;
+	cp->cp_pbdir &= ~0x00000cc0;
+	cp->cp_pbodr &= ~0x00000cc0;
+#endif
+
+	/* Allocate space for two buffer descriptors in the DP ram.
+	 * For now, this address seems OK, but it may have to
+	 * change with newer versions of the firmware.
+	 */
+	dpaddr = 0x0800;
+
+	/* Grab a few bytes from the top of memory for SMC FIFOs.
+	 */
+	memaddr = (bd->bi_memsize - 32) & ~15;
+
+	/* Set the physical address of the host memory buffers in
+	 * the buffer descriptors.
+	 */
+	rbdf = (cbd_t *)&cp->cp_dpmem[dpaddr];
+	rbdf->cbd_bufaddr = memaddr;
+	rbdf->cbd_sc = 0;
+	tbdf = rbdf + 1;
+	tbdf->cbd_bufaddr = memaddr+4;
+	tbdf->cbd_sc = 0;
+
+	/* Set up the uart parameters in the parameter ram.
+	*/
+	up->smc_rbase = dpaddr;
+	up->smc_tbase = dpaddr+sizeof(cbd_t);
+	up->smc_rfcr = SMC_EB;
+	up->smc_tfcr = SMC_EB;
+
+	/* Set UART mode, 8 bit, no parity, one stop.
+	 * Enable receive and transmit.
+	 */
+	sp->smc_smcmr = smcr_mk_clen(9) |  SMCMR_SM_UART;
+
+	/* Mask all interrupts and remove anything pending.
+	*/
+	sp->smc_smcm = 0;
+	sp->smc_smce = 0xff;
+
+	/* Set up the baud rate generator.
+	 * See 8xx_io/commproc.c for details.
+	 * This wires BRG1 to SMC1 and BRG2 to SMC2;
+	 */
+	cp->cp_simode = 0x10000000;
+	ui = bd->bi_intfreq / 16 / bd->bi_baudrate;
+#ifdef TQM_SMC2_CONSOLE
+	cp->cp_brgc2 =
+#else
+	cp->cp_brgc1 =
+#endif
+		((ui - 1) < 4096)
+		? (((ui - 1) << 1) | CPM_BRG_EN)
+		: ((((ui / 16) - 1) << 1) | CPM_BRG_EN | CPM_BRG_DIV16);
+
+#else /* CONFIG_MBX */
+	if (*MBX_CSR1 & CSR1_COMEN) {
+		/* COM1 is enabled.  Initialize SMC1 and use it for
+		 * the console port.
+		 */
+
+		/* Enable SDMA.
+		*/
+		((immap_t *)IMAP_ADDR)->im_siu_conf.sc_sdcr = 1;
+
+		/* Use Port B for SMCs instead of other functions.
+		*/
+		cp->cp_pbpar |= 0x00000cc0;
+		cp->cp_pbdir &= ~0x00000cc0;
+		cp->cp_pbodr &= ~0x00000cc0;
+
+		/* Allocate space for two buffer descriptors in the DP ram.
+		 * For now, this address seems OK, but it may have to
+		 * change with newer versions of the firmware.
+		 */
+		dpaddr = 0x0800;
+
+		/* Grab a few bytes from the top of memory.  EPPC-Bug isn't
+		 * running any more, so we can do this.
+		 */
+		memaddr = (bd->bi_memsize - 32) & ~15;
+
+		/* Set the physical address of the host memory buffers in
+		 * the buffer descriptors.
+		 */
+		rbdf = (cbd_t *)&cp->cp_dpmem[dpaddr];
+		rbdf->cbd_bufaddr = memaddr;
+		rbdf->cbd_sc = 0;
+		tbdf = rbdf + 1;
+		tbdf->cbd_bufaddr = memaddr+4;
+		tbdf->cbd_sc = 0;
+
+		/* Set up the uart parameters in the parameter ram.
+		*/
+		up->smc_rbase = dpaddr;
+		up->smc_tbase = dpaddr+sizeof(cbd_t);
+		up->smc_rfcr = SMC_EB;
+		up->smc_tfcr = SMC_EB;
+
+		/* Set UART mode, 8 bit, no parity, one stop.
+		 * Enable receive and transmit.
+		 */
+		sp->smc_smcmr = smcr_mk_clen(9) |  SMCMR_SM_UART;
+
+		/* Mask all interrupts and remove anything pending.
+		*/
+		sp->smc_smcm = 0;
+		sp->smc_smce = 0xff;
+
+		/* Set up the baud rate generator.
+		 * See 8xx_io/commproc.c for details.
+		 */
+		cp->cp_simode = 0x10000000;
+		cp->cp_brgc1 =
+			(((bd->bi_intfreq/16) / 9600) << 1) | CPM_BRG_EN;
+
+		/* Enable SMC1 for console output.
+		*/
+		*MBX_CSR1 &= ~CSR1_COMEN;
+	}
+	else {
+#endif /* ndef CONFIG_MBX */
+		/* SMCx is used as console port.
+		*/
+		tbdf = (cbd_t *)&cp->cp_dpmem[up->smc_tbase];
+		rbdf = (cbd_t *)&cp->cp_dpmem[up->smc_rbase];
+
+		/* Issue a stop transmit, and wait for it.
+		*/
+		cp->cp_cpcr = mk_cr_cmd(CPM_CR_CH_CONS,
+					CPM_CR_STOP_TX) | CPM_CR_FLG;
+		while (cp->cp_cpcr & CPM_CR_FLG);
+	}
+
+	/* Make the first buffer the only buffer.
+	*/
+	tbdf->cbd_sc |= BD_SC_WRAP;
+	rbdf->cbd_sc |= BD_SC_EMPTY | BD_SC_WRAP;
+
+	/* Single character receive.
+	*/
+	up->smc_mrblr = 1;
+	up->smc_maxidl = 0;
+
+	/* Initialize Tx/Rx parameters.
+	*/
+	cp->cp_cpcr = mk_cr_cmd(CPM_CR_CH_CONS, CPM_CR_INIT_TRX) | CPM_CR_FLG;
+	while (cp->cp_cpcr & CPM_CR_FLG);
+
+	/* Enable transmitter/receiver.
+	*/
+	sp->smc_smcmr |= SMCMR_REN | SMCMR_TEN;
+}
+
+void
+serial_putc(void *ignored, const char c)
+{
+	volatile cbd_t		*tbdf;
+	volatile char		*buf;
+	volatile smc_uart_t	*up;
+
+	up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_CONS];
+	tbdf = (cbd_t *)&cpmp->cp_dpmem[up->smc_tbase];
+
+	/* Wait for last character to go.
+	*/
+	buf = (char *)tbdf->cbd_bufaddr;
+	while (tbdf->cbd_sc & BD_SC_READY);
+
+	*buf = c;
+	tbdf->cbd_datlen = 1;
+	tbdf->cbd_sc |= BD_SC_READY;
+}
+
+char
+serial_getc(void *ignored)
+{
+	volatile cbd_t		*rbdf;
+	volatile char		*buf;
+	volatile smc_uart_t	*up;
+	char			c;
+
+	up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_CONS];
+	rbdf = (cbd_t *)&cpmp->cp_dpmem[up->smc_rbase];
+
+	/* Wait for character to show up.
+	*/
+	buf = (char *)rbdf->cbd_bufaddr;
+	while (rbdf->cbd_sc & BD_SC_EMPTY);
+	c = *buf;
+	rbdf->cbd_sc |= BD_SC_EMPTY;
+
+	return(c);
+}
+
+int
+serial_tstc(void *ignored)
+{
+	volatile cbd_t		*rbdf;
+	volatile smc_uart_t	*up;
+
+	up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_CONS];
+	rbdf = (cbd_t *)&cpmp->cp_dpmem[up->smc_rbase];
+
+	return(!(rbdf->cbd_sc & BD_SC_EMPTY));
+}

FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)