Internet Engineering Task Force (IETF)                   A. Rijhsinghani
Request for Comments: 6850                               Hewlett-Packard
Category: Standards Track                                     K. Zebrose
ISSN: 2070-1721                                              HW Embedded
                                                            January 2013


     Definitions of Managed Objects for Routing Bridges (RBridges)

Abstract

   This memo defines a portion of the Management Information Base (MIB)
   for use with network management protocols.  In particular, it defines
   objects for managing a Routing Bridge (RBridge), also known as a
   TRILL Switch, based on the IETF TRILL (Transparent Interconnection of
   Lots of Links) protocol.

Status of This Memo

   This is an Internet Standards Track document.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Further information on
   Internet Standards is available in Section 2 of RFC 5741.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   http://www.rfc-editor.org/info/rfc6850.

Copyright Notice

   Copyright (c) 2013 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.






Rijhsinghani & Zebrose       Standards Track                    [Page 1]

RFC 6850                RBridges: TRILL Base MIB            January 2013


Table of Contents

   1. Introduction ....................................................2
   2. The Internet-Standard Management Framework ......................3
   3. Overview ........................................................3
   4. Conventions .....................................................4
   5. Structure of the MIB Module .....................................4
      5.1. Textual Conventions ........................................4
      5.2. The rbridgeBase Subtree ....................................4
      5.3. The rbridgeFdb Subtree .....................................4
      5.4. The rbridgeVlan Subtree ....................................4
      5.5. The rbridgeEsadi Subtree ...................................4
      5.6. The rbridgeCounters Subtree ................................4
      5.7. The rbridgeSnooping Subtree ................................5
      5.8. The rbridgeDtree Subtree ...................................5
      5.9. The rbridgeTrill Subtree ...................................5
      5.10. The Notifications Subtree .................................5
   6. Relationship to Other MIB Modules ...............................5
      6.1. Relationship to IF-MIB .....................................5
      6.2. Relationship to BRIDGE-MIB .................................6
      6.3. Relationship to P-BRIDGE-MIB ...............................6
      6.4. Relationship to Q-BRIDGE-MIB ...............................6
      6.5. Relationship to IEEE8021-BRIDGE-MIB ........................7
      6.6. Relationship to IEEE8021-Q-BRIDGE-MIB ......................7
      6.7. Relationship to ISIS-MIB ...................................8
      6.8. MIB Modules Required for IMPORTS ...........................8
   7. Definition of the RBridge MIB Module ............................9
   8. Security Considerations ........................................55
   9. IANA Considerations ............................................56
   10. Contributors ..................................................56
   11. References ....................................................57
      11.1. Normative References .....................................57
      11.2. Informative References ...................................58

1.  Introduction

   This document describes a model for managing Routing Bridges
   (RBridges), also known as TRILL Switches, as defined in [RFC6325].
   RBridges provide optimal pair-wise forwarding without configuration
   using IS-IS routing and encapsulation of traffic.  RBridges are
   compatible with previous IEEE 802.1 customer bridges as well as IPv4
   and IPv6 routers and end nodes.  They are as invisible to current IP
   routers as bridges are and, like routers, they terminate the bridge
   spanning tree protocol.  In creating an RBridge management model, the
   device is viewed primarily as a customer bridge.  For a discussion of
   the problem addressed by TRILL (Transparent Interconnection of Lots
   of Links), see [RFC5556].




Rijhsinghani & Zebrose       Standards Track                    [Page 2]

RFC 6850                RBridges: TRILL Base MIB            January 2013


   RBridges support features specified for transparent bridges in
   IEEE 802.1, and the corresponding MIB modules are used to manage
   those features.  For IS-IS purposes, the corresponding MIB module is
   used to manage the protocol.  This MIB module specifies those objects
   that are TRILL-specific and hence not available in other MIB modules.

2.  The Internet-Standard Management Framework

   For a detailed overview of the documents that describe the current
   Internet-Standard Management Framework, please refer to section 7 of
   RFC 3410 [RFC3410].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  MIB objects are generally
   accessed through the Simple Network Management Protocol (SNMP).
   Objects in the MIB are defined using the mechanisms defined in the
   Structure of Management Information (SMI).  This memo specifies a MIB
   module that is compliant to the SMIv2, which is described in STD 58,
   RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
   [RFC2580].

3.  Overview

   The RBridge MIB module is intended as an overall framework for
   managing RBridges, also known as TRILL Switches.  Where possible, the
   MIB references existing MIB definitions in order to maximize reuse.
   This results in a considerable emphasis on the relationship with
   other MIB modules.

   Starting with the physical interfaces, there are requirements for
   certain elements of the IF-MIB to be implemented.  These elements are
   required in order to connect the per-port parameters to higher-level
   functions of the physical device.

   Transparent bridging, VLANs, traffic classes, and multicast filtering
   are supported by the TRILL protocol, and the corresponding management
   is expected to conform to the BRIDGE-MIB module [RFC4188] and to the
   P-BRIDGE-MIB and Q-BRIDGE-MIB modules [RFC4363].

   The IS-IS routing protocol is used in order to determine the optimum
   pair-wise forwarding path.  This protocol is managed using the IS-IS
   MIB module defined in [RFC4444].  Since the TRILL protocol specifies
   the use of a single level and a fixed area address of zero, some
   IS-IS MIB objects are not applicable.  Some IS-IS MIB objects are
   used in the TRILL protocol.






Rijhsinghani & Zebrose       Standards Track                    [Page 3]

RFC 6850                RBridges: TRILL Base MIB            January 2013


4.  Conventions

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   RFC 2119 [RFC2119].

5.  Structure of the MIB Module

   Objects in this MIB module are arranged into subtrees.  Each subtree
   is organized as a set of related objects.  The various subtrees are
   shown below.  These are supplemented with required elements of the
   IF-MIB, ISIS-MIB, BRIDGE-MIB, P-BRIDGE-MIB, Q-BRIDGE-MIB, and IEEE
   Bridge MIB modules.

5.1.  Textual Conventions

   Textual conventions are defined to represent object types relevant to
   TRILL.

5.2.  The rbridgeBase Subtree

   This subtree contains system- and port-specific objects applicable to
   all RBridges.

5.3.  The rbridgeFdb Subtree

   This subtree contains objects applicable to the forwarding database
   used by the RBridge in making packet-forwarding decisions.  Because
   it contains additional information used by the TRILL protocol not
   applicable to 802.1D/Q bridges, it is a superset of the corresponding
   subtrees defined in the BRIDGE-MIB and Q-BRIDGE-MIB.

5.4.  The rbridgeVlan Subtree

   This subtree describes objects applicable to VLANs configured on the
   RBridge.

5.5.  The rbridgeEsadi Subtree

   This subtree describes objects relevant to RBridges that support the
   optional End-Station Address Distribution Information (ESADI)
   protocol.

5.6.  The rbridgeCounters Subtree

   This subtree contains statistics maintained by RBridges that can aid
   in monitoring and troubleshooting networks connected by them.



Rijhsinghani & Zebrose       Standards Track                    [Page 4]

RFC 6850                RBridges: TRILL Base MIB            January 2013


5.7.  The rbridgeSnooping Subtree

   This subtree describes objects applicable to RBridges capable of
   snooping IPv4 and/or IPv6 multicast control frames and pruning IP
   multicast traffic based on detection of IP multicast routers and
   listeners.

5.8.  The rbridgeDtree Subtree

   This subtree contains objects relevant to distribution trees computed
   by RBridges for the forwarding of multi-destination frames.

5.9.  The rbridgeTrill Subtree

   This subtree contains objects applicable to the TRILL IS-IS protocol,
   beyond what is available in the ISIS-MIB.

5.10.  The Notifications Subtree

   The defined notifications are focused on the TRILL protocol
   functionality.  Notifications are defined for changes in the
   Designated RBridge status and the topology.

6.  Relationship to Other MIB Modules

   The IF-MIB, BRIDGE-MIB, P-BRIDGE-MIB, Q-BRIDGE-MIB,
   IEEE8021-BRIDGE-MIB, IEEE8021-Q-BRIDGE-MIB, and ISIS-MIB modules all
   contain objects relevant to the RBridge MIB.  Management objects
   contained in these modules are not duplicated here, to reduce overlap
   to the extent possible.

   The Bridge MIB modules were originally written in the IETF and
   implemented by many vendors.  Per [RFC4663], this has recently been
   transferred to the IEEE 802.1 working group.  As vendors may have
   implemented either the IETF or IEEE Bridge MIB modules, this RBridge
   MIB module is designed to work with either one.

6.1.  Relationship to IF-MIB

   The port identification elements MUST be implemented in order to
   allow them to be cross-referenced.  The Interfaces MIB [RFC2863]
   requires that any MIB module that is an adjunct of the Interfaces MIB
   clarify specific areas within the Interfaces MIB module.  These areas
   were intentionally left vague in the Interfaces MIB module to avoid
   over-constraining the MIB, thereby precluding management of certain
   media types.  Section 4 of [RFC2863] enumerates several areas that a





Rijhsinghani & Zebrose       Standards Track                    [Page 5]

RFC 6850                RBridges: TRILL Base MIB            January 2013


   media-specific MIB module must clarify.  The implementor is referred
   to [RFC2863] in order to understand the general intent of these
   areas.

6.2.  Relationship to BRIDGE-MIB

   The following subtrees in the BRIDGE-MIB [RFC4188] contain
   information relevant to RBridges when the corresponding functionality
   is implemented.

   o  dot1dBase

   o  dot1dTp

   o  dot1dStatic

6.3.  Relationship to P-BRIDGE-MIB

   The following subtrees in the P-BRIDGE-MIB [RFC4363] contain
   information relevant to RBridges when the corresponding functionality
   is implemented.

   o  dot1dExtBase

   o  dot1dPriority

   o  dot1dGarp

   o  dot1dGmrp

   o  dot1dTpHCPortTable

   o  dot1dTpPortOverflowTable

6.4.  Relationship to Q-BRIDGE-MIB

   The following groups in the Q-BRIDGE-MIB [RFC4363] contain
   information relevant to RBridges when the corresponding functionality
   is implemented.  This functionality is also contained in the
   IEEE8021-Q-BRIDGE-MIB.

   o  dot1qBase

   o  dot1qTp

   o  dot1qStatic





Rijhsinghani & Zebrose       Standards Track                    [Page 6]

RFC 6850                RBridges: TRILL Base MIB            January 2013


   o  dot1qVlan

   o  dot1vProtocol

6.5.  Relationship to IEEE8021-BRIDGE-MIB

   The following subtrees in the IEEE8021-BRIDGE-MIB contain information
   relevant to RBridges when the corresponding functionality is
   implemented.

   o  ieee8021BridgeBase

   o  ieee8021BridgeTp

   o  ieee8021BridgePriority

   o  ieee8021BridgeMrp

   o  ieee8021BridgeMmrp

   o  ieee8021BridgeInternalLan

   o  ieee8021BridgeDot1d

6.6.  Relationship to IEEE8021-Q-BRIDGE-MIB

   The following subtrees in the IEEE8021-Q-BRIDGE-MIB contain
   information relevant to RBridges when the corresponding functionality
   is implemented.

   o  ieee8021QBridgeBase

   o  ieee8021QBridgeTp

   o  ieee8021QBridgeStatic

   o  ieee8021QBridgeVlan

   o  ieee8021QBridgeProtocol












Rijhsinghani & Zebrose       Standards Track                    [Page 7]

RFC 6850                RBridges: TRILL Base MIB            January 2013


6.7.  Relationship to ISIS-MIB

   "Management Information Base for Intermediate System to Intermediate
   System (IS-IS)" [RFC4444] defines a MIB module for the IS-IS routing
   protocol when it is used to construct routing tables for IP networks.
   While most of these objects are applicable to the TRILL layer 2
   implementation, note the IS-IS constraints for the current version of
   TRILL [RFC6325]:

   o  The TRILL IS-IS instance uses a single Level 1 IS-IS area.

   o  The TRILL Level 1 IS-IS area uses the fixed area address zero.

   o  The TRILL IS-IS instance is not used for IP address advertisement.

   o  The TRILL IS-IS instance is used for only a single protocol:
      TRILL.

   Accordingly, tables that report IP address reachability and tables
   that allow configuration or reporting of multiple IS-IS areas,
   multiple IS-IS levels, or multiple protocols will be empty in the
   ISIS-MIB module for the current version of TRILL.

   Note also that when more than one instance of the IS-IS protocol is
   running on a device, as in the case of a device performing both
   RBridge and IS-IS IP router functions, multiple instances of the
   ISIS-MIB module can be distinguished by the use of SNMPv3 contexts or
   SNMPv1 communities.

6.8.  MIB Modules Required for IMPORTS

   The following MIB module imports objects from the SNMPv2-SMI
   [RFC2578], SNMPv2-TC [RFC2579], SNMPv2-CONF [RFC2580], IF-MIB
   [RFC2863], INET-ADDRESS-MIB [RFC4001], BRIDGE-MIB [RFC4188],
   and Q-BRIDGE-MIB [RFC4363].  (The IEEE Bridge MIB modules import
   similar TCs.)















Rijhsinghani & Zebrose       Standards Track                    [Page 8]

RFC 6850                RBridges: TRILL Base MIB            January 2013


7.  Definition of the RBridge MIB Module

   RBRIDGE-MIB DEFINITIONS ::= BEGIN

   -- ---------------------------------------------------------- --
   -- MIB for RBRIDGE devices, also known as TRILL Switches
   -- ---------------------------------------------------------- --
   IMPORTS
       MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
       Counter32, Counter64, Unsigned32, mib-2
           FROM SNMPv2-SMI            -- RFC2578
       TEXTUAL-CONVENTION, TruthValue, MacAddress, RowStatus
           FROM SNMPv2-TC             -- RFC2579
       MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
           FROM SNMPv2-CONF           -- RFC2580
       VlanId, PortList
           FROM Q-BRIDGE-MIB          -- RFC4363
       InetAddress, InetAddressType
           FROM INET-ADDRESS-MIB      -- RFC4001
       BridgeId
           FROM BRIDGE-MIB            -- RFC4188
       InterfaceIndex
           FROM IF-MIB                -- RFC2863
       ;

   rbridgeMIB MODULE-IDENTITY
   LAST-UPDATED "201301070000Z"
   ORGANIZATION "IETF TRILL Working Group"
   CONTACT-INFO
        "http://datatracker.ietf.org/wg/trill/charter/
        Email: trill@ietf.org

               Anil Rijhsinghani
               Hewlett-Packard
          Tel: +1 508 323 1251
        Email: anil@charter.net

               Kate Zebrose
               HW Embedded
          Tel: +1 617 840 9673
        Email: zebrose@alum.mit.edu"

       DESCRIPTION
           "The RBridge MIB module for managing switches that support
           the TRILL protocol."

   REVISION     "201301070000Z"




Rijhsinghani & Zebrose       Standards Track                    [Page 9]

RFC 6850                RBridges: TRILL Base MIB            January 2013


   DESCRIPTION
        "Initial version, published as RFC 6850.

        Copyright (c) 2013 IETF Trust and the persons identified as
        authors of the code.  All rights reserved.

        Redistribution and use in source and binary forms, with or
        without modification, is permitted pursuant to, and subject to
        the license terms contained in, the Simplified BSD License set
        forth in Section 4.c of the IETF Trust's Legal Provisions
        Relating to IETF Documents
        (http://trustee.ietf.org/license-info)."

        ::= { mib-2 214 }


   -- ---------------------------------------------------------- --
   -- Subtrees in the RBridge MIB
   -- ---------------------------------------------------------- --

   rbridgeNotifications  OBJECT IDENTIFIER ::= { rbridgeMIB 0 }
   rbridgeObjects        OBJECT IDENTIFIER ::= { rbridgeMIB 1 }
   rbridgeConformance    OBJECT IDENTIFIER ::= { rbridgeMIB 2 }

   rbridgeBase           OBJECT IDENTIFIER ::= { rbridgeObjects 1 }
   rbridgeFdb            OBJECT IDENTIFIER ::= { rbridgeObjects 2 }
   rbridgeVlan           OBJECT IDENTIFIER ::= { rbridgeObjects 3 }
   rbridgeEsadi          OBJECT IDENTIFIER ::= { rbridgeObjects 4 }
   rbridgeCounter        OBJECT IDENTIFIER ::= { rbridgeObjects 5 }
   rbridgeSnooping       OBJECT IDENTIFIER ::= { rbridgeObjects 6 }
   rbridgeDtree          OBJECT IDENTIFIER ::= { rbridgeObjects 7 }
   rbridgeTrill          OBJECT IDENTIFIER ::= { rbridgeObjects 8 }

   -- ---------------------------------------------------------- --
   -- Type Definitions
   -- ---------------------------------------------------------- --

   RbridgeAddress ::= TEXTUAL-CONVENTION
       DISPLAY-HINT "1x:"
       STATUS current
       DESCRIPTION
           "The Media Access Control (MAC) address used by an RBridge
           port.  This may match the RBridge IS-IS SystemID."
       SYNTAX OCTET STRING (SIZE (6))







Rijhsinghani & Zebrose       Standards Track                   [Page 10]

RFC 6850                RBridges: TRILL Base MIB            January 2013


   RbridgeNickname ::= TEXTUAL-CONVENTION
       DISPLAY-HINT "d"
       STATUS current
       DESCRIPTION
           "The 16-bit identifier used in TRILL as an
           abbreviation for the RBridge's 48-bit IS-IS System ID.
           The value 0 means a nickname is not specified, the values
           0xFFC0 through 0xFFFE are reserved for future allocation,
           and the value 0xFFFF is permanently reserved."
       REFERENCE
           "RFC 6325, Section 3.7"
       SYNTAX Unsigned32 (0..65471)

   --
   -- the rbridgeBase subtree
   --
   -- Implementation of the rbridgeBase subtree is mandatory for all
   -- RBridges.
   --

   rbridgeBaseTrillVersion OBJECT-TYPE
       SYNTAX      Unsigned32
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The maximum TRILL version number that this RBridge
           supports."
       REFERENCE
           "RFC 6325, Section 3.2"
       ::= { rbridgeBase 1 }

   rbridgeBaseNumPorts OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "ports"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The number of ports controlled by this RBridge."
       REFERENCE
           "RFC 6325, Section 2.6.1"
       ::= { rbridgeBase 2 }

   rbridgeBaseForwardDelay OBJECT-TYPE
       SYNTAX      Unsigned32 (4..30)
       UNITS       "seconds"
       MAX-ACCESS  read-write
       STATUS      current




Rijhsinghani & Zebrose       Standards Track                   [Page 11]

RFC 6850                RBridges: TRILL Base MIB            January 2013


       DESCRIPTION
           "Modified aging time for address entries after an appointed
           forwarder change.

           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Section 4.8.3"
       ::= { rbridgeBase 3 }

   rbridgeBaseUniMultipathEnable OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "The enabled status of unicast TRILL multipathing.
           It is enabled when true.

           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Appendix C"
       ::= { rbridgeBase 4 }

   rbridgeBaseMultiMultipathEnable OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "The enabled status of multi-destination TRILL multipathing.
           It is enabled when true.

           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Appendix C"
       ::= { rbridgeBase 5 }

   rbridgeBaseAcceptEncapNonadj OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "Accept TRILL-encapsulated frames from a neighbor with which
           this RBridge does not have an IS-IS adjacency, when the value
           of this object is 'true'.





Rijhsinghani & Zebrose       Standards Track                   [Page 12]

RFC 6850                RBridges: TRILL Base MIB            January 2013


           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Section 4.6.2"
       ::= { rbridgeBase 6 }

   rbridgeBaseNicknameNumber OBJECT-TYPE
       SYNTAX      Unsigned32 (1..256)
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "The number of nicknames this RBridge should acquire.
           These can be acquired dynamically or configured
           statically.  This value represents the maximum
           number of entries in rbridgeBaseNicknameTable.

           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Section 3.7.3"
       ::= { rbridgeBase 7 }

   -- ---------------------------------------------------------- --
   -- The RBridge Base Nickname Table
   -- ---------------------------------------------------------- --

   rbridgeBaseNicknameTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF RbridgeBaseNicknameEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "A table that contains information about nicknames
           configured by an operator or learned dynamically
           by this RBridge."
       REFERENCE
           "RFC 6325, Section 3.7"
       ::= { rbridgeBase 8 }

   rbridgeBaseNicknameEntry OBJECT-TYPE
       SYNTAX      RbridgeBaseNicknameEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "A list of information for each nickname of the RBridge."
       REFERENCE
           "RFC 6325, Section 3.7"
       INDEX  { rbridgeBaseNicknameName }
       ::= { rbridgeBaseNicknameTable 1 }



Rijhsinghani & Zebrose       Standards Track                   [Page 13]

RFC 6850                RBridges: TRILL Base MIB            January 2013


   RbridgeBaseNicknameEntry ::=
       SEQUENCE {
           rbridgeBaseNicknameName
               RbridgeNickname,
           rbridgeBaseNicknamePriority
               Unsigned32,
           rbridgeBaseNicknameDtrPriority
               Unsigned32,
           rbridgeBaseNicknameType
               INTEGER,
           rbridgeBaseNicknameRowStatus
               RowStatus
       }

   rbridgeBaseNicknameName OBJECT-TYPE
       SYNTAX      RbridgeNickname
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "Nicknames are 16-bit quantities that act as
           abbreviations for RBridge's 48-bit IS-IS System ID to
           achieve a more compact encoding."
       REFERENCE
           "RFC 6325, Section 3.7"
       ::= { rbridgeBaseNicknameEntry 1 }

   rbridgeBaseNicknamePriority OBJECT-TYPE
       SYNTAX      Unsigned32 (0..255)
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "This RBridge's priority to hold this nickname.  When
           the nickname is configured, the default value of this
           object is 192.  When the nickname is configured, the most
           significant bit (0x80) must be set and the bottom 7 bits
           have the default value of 0x40, so 0x80 + 0x40 == 0xC0,
           which is 192 decimal.  Additionally, the bottom 7 bits
           could be configured to a value other than 0x40.

           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Section 3.7"
       DEFVAL      { 192 }
       ::= { rbridgeBaseNicknameEntry 2 }






Rijhsinghani & Zebrose       Standards Track                   [Page 14]

RFC 6850                RBridges: TRILL Base MIB            January 2013


   rbridgeBaseNicknameDtrPriority OBJECT-TYPE
       SYNTAX      Unsigned32 (1..65535)
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The distribution tree root priority for this nickname.
           The default value of this object is 32768.

           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Section 4.5"
       DEFVAL      { 32768 }
       ::= { rbridgeBaseNicknameEntry 3 }

   rbridgeBaseNicknameType OBJECT-TYPE
       SYNTAX      INTEGER {
                       static(1),
                       dynamic(2)
                   }
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "This object indicates the status of the entry.  The
           default value is static(1).
               static(1) - this entry has been configured and
                   will remain after the next reset of the RBridge.
               dynamic(2) - this entry has been acquired by the
                   RBridge nickname acquisition protocol."
       REFERENCE
           "RFC 6325, Section 3.7"
       DEFVAL      { static }
       ::= { rbridgeBaseNicknameEntry 4 }

   rbridgeBaseNicknameRowStatus OBJECT-TYPE
       SYNTAX      RowStatus
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "This object indicates the status of the entry."
       ::= { rbridgeBaseNicknameEntry 5 }










Rijhsinghani & Zebrose       Standards Track                   [Page 15]

RFC 6850                RBridges: TRILL Base MIB            January 2013


   -- ---------------------------------------------------------- --
   -- The RBridge Port Table
   -- ---------------------------------------------------------- --

   rbridgeBasePortTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF RbridgeBasePortEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "A table that contains generic information about every
           port that is associated with this RBridge."
       REFERENCE
           "RFC 6325, Section 5.3"
       ::= { rbridgeBase 9 }

   rbridgeBasePortEntry OBJECT-TYPE
       SYNTAX      RbridgeBasePortEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "A list of information for each port of the bridge."
       REFERENCE
           "RFC 6325, Section 5.3"
       INDEX  { rbridgeBasePort }
       ::= { rbridgeBasePortTable 1 }

   RbridgeBasePortEntry ::=
       SEQUENCE {
           rbridgeBasePort
               Unsigned32,
           rbridgeBasePortIfIndex
               InterfaceIndex,
           rbridgeBasePortDisable
               TruthValue,
           rbridgeBasePortTrunkPort
               TruthValue,
           rbridgeBasePortAccessPort
               TruthValue,
           rbridgeBasePortP2pHellos
               TruthValue,
           rbridgeBasePortState
               INTEGER,
           rbridgeBasePortInhibitionTime
               Unsigned32,
           rbridgeBasePortDisableLearning
               TruthValue,
           rbridgeBasePortDesiredDesigVlan
               VlanId,



Rijhsinghani & Zebrose       Standards Track                   [Page 16]

RFC 6850                RBridges: TRILL Base MIB            January 2013


           rbridgeBasePortDesigVlan
               VlanId,
           rbridgeBasePortStpRoot
               BridgeId,
           rbridgeBasePortStpRootChanges
               Counter32,
           rbridgeBasePortStpWiringCloset
               BridgeId
   }

   rbridgeBasePort OBJECT-TYPE
       SYNTAX      Unsigned32 (1..65535)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "The port number of the port for which this entry
           contains RBridge management information."
       REFERENCE
           "RFC 6325, Section 5.3"
       ::= { rbridgeBasePortEntry 1 }

   rbridgeBasePortIfIndex OBJECT-TYPE
       SYNTAX      InterfaceIndex
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The value of the instance of the ifIndex object,
           defined in the IF-MIB, for the interface corresponding
           to this port.  The RBridge port sits on top of
           this interface."
       ::= { rbridgeBasePortEntry 2 }

   rbridgeBasePortDisable OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "Disable port bit.  When this bit is set (true), all frames
           received or to be transmitted are discarded, with the
           possible exception of some layer 2 control frames that may
           be generated and transmitted or received and processed
           locally.  Default value is 'false'.

           The value of this object MUST be retained across
           re-initializations of the management system."






Rijhsinghani & Zebrose       Standards Track                   [Page 17]

RFC 6850                RBridges: TRILL Base MIB            January 2013


       REFERENCE
           "RFC 6325, Section 4.9.1"
       DEFVAL      { false }
       ::= { rbridgeBasePortEntry 3 }

   rbridgeBasePortTrunkPort OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "End-station service disable (trunk port) bit.  When this bit
           is set (true), all native frames received on the port and all
           native frames that would have been sent on the port are
           discarded.  Default value is 'false'.

           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Section 4.9.1"
       DEFVAL      { false }
       ::= { rbridgeBasePortEntry 4 }

   rbridgeBasePortAccessPort OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "TRILL traffic disable (access port) bit.  If this bit is
           set, the goal is to avoid sending any TRILL frames, except
           TRILL-Hello frames, on the port, since it is intended only
           for native end-station traffic.  This ensures that the link
           is not on the shortest path for any destination.  Default
           value is 'false'.

           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Section 4.9.1"
       DEFVAL      { false }
       ::= { rbridgeBasePortEntry 5 }

   rbridgeBasePortP2pHellos OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "Use point-to-point (P2P) Hellos bit.  If this bit is set,
           Hellos sent on this port are IS-IS P2P Hellos, not the



Rijhsinghani & Zebrose       Standards Track                   [Page 18]

RFC 6850                RBridges: TRILL Base MIB            January 2013


           default TRILL-Hellos.  In addition, the IS-IS P2P three-way
           handshake is used on P2P RBridge links.  Default value is
           'false'.

           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Section 4.9.1"
       DEFVAL      { false }
       ::= { rbridgeBasePortEntry 6 }

   rbridgeBasePortState OBJECT-TYPE
       SYNTAX      INTEGER {
                          uninhibited(1),
                          portInhibited(2),
                          vlanInhibited(3),
                          disabled(4),
                          broken(5)
                      }
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The port's current state.  If the entire port is
           inhibited, its state is portInhibited(2).  If specific VLANs
           are inhibited, the state is vlanInhibited(3), and
           rbridgeVlanPortTable will tell which VLANs are inhibited.
           For ports that are disabled (see rbridgeBasePortDisable),
           this object will have a value of disabled(4).  If the
           RBridge has detected a port that is malfunctioning, it will
           place that port into the broken(5) state."
       REFERENCE
           "RFC 6325, Section 4.2.4.3"
       ::= { rbridgeBasePortEntry 7 }

   rbridgeBasePortInhibitionTime OBJECT-TYPE
       SYNTAX      Unsigned32
       UNITS       "seconds"
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "Time in seconds that this RBridge will inhibit forwarding
           on this port after it observes a spanning tree root bridge
           change on a link or receives conflicting VLAN forwarder
           information.  The default value is 30.

           The value of this object MUST be retained across
           re-initializations of the management system."




Rijhsinghani & Zebrose       Standards Track                   [Page 19]

RFC 6850                RBridges: TRILL Base MIB            January 2013


       REFERENCE
           "RFC 6325, Section 4.2.4.3"
       DEFVAL      { 30 }
       ::= { rbridgeBasePortEntry 8 }

   rbridgeBasePortDisableLearning OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "Disable learning of MAC addresses seen on this port.
           To disable learning, the value of this object must be
           set to 'true'.  The default is 'false'.

           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Section 4.8"
       DEFVAL      { false }
       ::= { rbridgeBasePortEntry 9 }

   rbridgeBasePortDesiredDesigVlan OBJECT-TYPE
       SYNTAX      VlanId
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "The VLAN that a Designated RBridge (DRB) will specify in
           its TRILL-Hellos as the VLAN to be used by all RBridges on
           the link for TRILL frames.  This VLAN must be enabled on
           this port.

           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Section 4.4.3"
       ::= { rbridgeBasePortEntry 10 }

   rbridgeBasePortDesigVlan OBJECT-TYPE
       SYNTAX      VlanId
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The VLAN being used on this link for TRILL frames."
       REFERENCE
           "RFC 6325, Section 4.4.3"
       ::= { rbridgeBasePortEntry 11 }





Rijhsinghani & Zebrose       Standards Track                   [Page 20]

RFC 6850                RBridges: TRILL Base MIB            January 2013


   rbridgeBasePortStpRoot OBJECT-TYPE
       SYNTAX      BridgeId
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The bridge identifier of the root of the spanning tree,
           as learned from a Bridge PDU (BPDU) received on this port.
           For the Multiple Spanning Tree Protocol (MSTP), this is
           the root bridge of the Common and Internal Spanning Tree
           (CIST).  If no BPDU has been heard, the value returned
           is a string of zeros."
       REFERENCE
           "RFC 6325, Section 4.2.4.3"
       ::= { rbridgeBasePortEntry 12 }

   rbridgeBasePortStpRootChanges OBJECT-TYPE
       SYNTAX      Counter32
       UNITS       "changes"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The number of times a change in the root bridge is seen from
           spanning tree BPDUs received on this port, indicating a
           change in bridged LAN topology.  Each such change may cause
           the port to be inhibited for a period of time.  This counter
           should be synchronized with ifCounterDiscontinuityTime.

           Discontinuities in the value of this counter can occur
           at re-initialization of the management system."
       REFERENCE
           "RFC 6325, Section 4.9.3.2"
       ::= { rbridgeBasePortEntry 13 }

   rbridgeBasePortStpWiringCloset OBJECT-TYPE
       SYNTAX      BridgeId
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "The Bridge ID to be used as the spanning tree root in BPDUs
           sent for the Wiring Closet topology solution described in
           [RFC6325].  Note that the same value of this object must be
           set on all RBridge ports participating in this solution.
           The default value is all 0s.  A non-zero value configured
           into this object indicates that this solution is in use.

           The value of this object MUST be retained across
           re-initializations of the management system."




Rijhsinghani & Zebrose       Standards Track                   [Page 21]

RFC 6850                RBridges: TRILL Base MIB            January 2013


       REFERENCE
           "RFC 6325, Appendix A.3.3"
       ::= { rbridgeBasePortEntry 14 }

   -- -------------------------------------------------------------
   -- RBridge Forwarding Database
   -- -------------------------------------------------------------

   rbridgeConfidenceNative OBJECT-TYPE
       SYNTAX      Unsigned32 (0..255)
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "The confidence level associated with MAC addresses
           learned from native frames.  This is applicable to
           all RBridge ports.

           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Section 4.8.1"
       ::= { rbridgeFdb 1 }

   rbridgeConfidenceDecap OBJECT-TYPE
       SYNTAX      Unsigned32 (0..255)
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "The confidence level associated with inner MAC addresses
           learned after decapsulation of a TRILL data frame.
           This is applicable to all RBridge ports.

           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Section 4.8.1"
       ::= { rbridgeFdb 2 }

   rbridgeConfidenceStatic OBJECT-TYPE
       SYNTAX      Unsigned32 (0..255)
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "The confidence level associated with MAC addresses that
           are statically configured.  The default value is 255.

           The value of this object MUST be retained across
           re-initializations of the management system."



Rijhsinghani & Zebrose       Standards Track                   [Page 22]

RFC 6850                RBridges: TRILL Base MIB            January 2013


       REFERENCE
           "RFC 6325, Section 4.8.2"
       DEFVAL      { 255 }
       ::= { rbridgeFdb 3 }


   -- -------------------------------------------------------------
   -- Multiple Forwarding Databases for RBridges
   --
   -- This allows for an instance per FdbId, as defined in the
   -- Bridge MIB.
   --
   -- Each VLAN may have an independent FDB, or multiple VLANs may
   -- share one.
   -- -------------------------------------------------------------

   rbridgeUniFdbTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF RbridgeUniFdbEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "A table that contains information about unicast entries
           for which the device has forwarding and/or filtering
           information.  This information is used by the
           transparent bridging function in determining how to
           propagate a received frame."
       REFERENCE
           "RFC 6325, Section 4.8"
       ::= { rbridgeFdb 4 }

   rbridgeUniFdbEntry OBJECT-TYPE
       SYNTAX      RbridgeUniFdbEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "Information about a specific unicast MAC address for
           which the RBridge has some forwarding and/or filtering
           information."
       INDEX   { rbridgeFdbId, rbridgeUniFdbAddr }
       ::= { rbridgeUniFdbTable 1 }

   RbridgeUniFdbEntry ::=
       SEQUENCE {
           rbridgeFdbId
               Unsigned32,
           rbridgeUniFdbAddr
               MacAddress,




Rijhsinghani & Zebrose       Standards Track                   [Page 23]

RFC 6850                RBridges: TRILL Base MIB            January 2013


           rbridgeUniFdbPort
               Unsigned32,
           rbridgeUniFdbNickname
               RbridgeNickname,
           rbridgeUniFdbConfidence
               Unsigned32,
           rbridgeUniFdbStatus
               INTEGER
       }

   rbridgeFdbId OBJECT-TYPE
       SYNTAX      Unsigned32 (0..4294967295)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "The identity of this Filtering Database."
       ::= { rbridgeUniFdbEntry 1 }

   rbridgeUniFdbAddr OBJECT-TYPE
       SYNTAX      MacAddress
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "A unicast MAC address for which the device has
           forwarding information."
       ::= { rbridgeUniFdbEntry 2 }

   rbridgeUniFdbPort OBJECT-TYPE
       SYNTAX      Unsigned32 (0..65535)
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "Either the value '0', or the RBridge port number of the
           port on which a frame having a source address equal to the
           value of the corresponding instance of rbridgeUniFdbAddr
           has been seen.  A value of '0' indicates that the port
           number has not been learned but that the device does have
           some information about this MAC address.

           Implementors are encouraged to assign the port value to
           this object whenever it is available, even for addresses
           for which the corresponding value of rbridgeUniFdbStatus is
           not learned(3)."
       ::= { rbridgeUniFdbEntry 3 }

   rbridgeUniFdbNickname OBJECT-TYPE
       SYNTAX      RbridgeNickname
       MAX-ACCESS  read-only



Rijhsinghani & Zebrose       Standards Track                   [Page 24]

RFC 6850                RBridges: TRILL Base MIB            January 2013


       STATUS      current
       DESCRIPTION
           "The RBridge nickname that is placed in the egress
           nickname field of a TRILL frame sent to this
           rbridgeFdbAddress in this rbridgeFdbId."
       REFERENCE
           "RFC 6325, Section 4.8.1"
       ::= { rbridgeUniFdbEntry 4 }

   rbridgeUniFdbConfidence OBJECT-TYPE
       SYNTAX      Unsigned32 (0..255)
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The confidence level associated with this entry."
       REFERENCE
           "RFC 6325, Section 4.8.1"
       ::= { rbridgeUniFdbEntry 5 }

   rbridgeUniFdbStatus OBJECT-TYPE
       SYNTAX      INTEGER {
                       other(1),
                       invalid(2),
                       learned(3),
                       self(4),
                       mgmt(5),
                       esadi(6)
                   }
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The status of this entry.  The meanings of the values
           are:
               other(1) - none of the following.
               invalid(2) - this entry is no longer valid (e.g., it
                   was learned but has since aged out) but has not
                   yet been flushed from the table.
               learned(3) - the information in this entry was learned
                   and is being used.
               self(4) - the value of the corresponding instance of
                   rbridgeFdbAddress represents one of the device's
                   addresses.  The corresponding instance of
                   rbridgeFdbPort indicates which of the device's
                   ports has this address.







Rijhsinghani & Zebrose       Standards Track                   [Page 25]

RFC 6850                RBridges: TRILL Base MIB            January 2013


               mgmt(5) - the value of the corresponding instance of
                   rbridgeFdbAddress was configured by management.
               esadi(6) - the value of the corresponding instance of
                   rbridgeFdbAddress was learned from ESADI."
       ::= { rbridgeUniFdbEntry 6 }

   -- -------------------------------------------------------------
   -- RBridge Forwarding Information Base (FIB)
   -- -------------------------------------------------------------

   rbridgeUniFibTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF RbridgeUniFibEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "A table that contains information about nicknames known by
           the RBridge.  If Equal-Cost Multipath (ECMP) is implemented,
           there are as many entries for a nickname as there are ECMP
           paths available for it."
       ::= { rbridgeFdb 5 }

   rbridgeUniFibEntry OBJECT-TYPE
       SYNTAX      RbridgeUniFibEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "A list of information about nicknames known by the RBridge.
           If ECMP is implemented, there are as many entries as there
           are ECMP paths available for a given nickname."
       INDEX   { rbridgeUniFibNickname, rbridgeUniFibPort,
                 rbridgeUniFibNextHop }
       ::= { rbridgeUniFibTable 1 }

   RbridgeUniFibEntry ::=
       SEQUENCE {
           rbridgeUniFibNickname
               RbridgeNickname,
           rbridgeUniFibPort
               Unsigned32,
           rbridgeUniFibNextHop
               RbridgeNickname,
           rbridgeUniFibHopCount
               Unsigned32
       }

   rbridgeUniFibNickname OBJECT-TYPE
       SYNTAX      RbridgeNickname
       MAX-ACCESS  not-accessible



Rijhsinghani & Zebrose       Standards Track                   [Page 26]

RFC 6850                RBridges: TRILL Base MIB            January 2013


       STATUS      current
       DESCRIPTION
           "An RBridge nickname for which this RBridge has
           forwarding information."
       ::= { rbridgeUniFibEntry 1 }

   rbridgeUniFibPort OBJECT-TYPE
       SYNTAX      Unsigned32 (0..65535)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "The RBridge port number of the port attached to the
           next-hop RBridge for the path towards the RBridge whose
           nickname is specified in this entry."
       ::= { rbridgeUniFibEntry 2 }

   rbridgeUniFibNextHop OBJECT-TYPE
       SYNTAX      RbridgeNickname
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "The nickname of the next-hop RBridge for the path
           towards the RBridge whose nickname is specified in this
           entry."
       ::= { rbridgeUniFibEntry 3 }

   rbridgeUniFibHopCount OBJECT-TYPE
       SYNTAX      Unsigned32
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The hop count from this ingress RBridge to the egress
           RBridge whose nickname is specified in
           rbridgeUniFibNickname."
       ::= { rbridgeUniFibEntry 4 }

   rbridgeMultiFibTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF RbridgeMultiFibEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "A table that contains information about egress nicknames
           used for multi-destination frame forwarding by this
           RBridge."
       ::= { rbridgeFdb 6 }






Rijhsinghani & Zebrose       Standards Track                   [Page 27]

RFC 6850                RBridges: TRILL Base MIB            January 2013


   rbridgeMultiFibEntry OBJECT-TYPE
       SYNTAX      RbridgeMultiFibEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "A list of information about egress nicknames used for
           multi-destination frame forwarding by this RBridge."
       INDEX   { rbridgeMultiFibNickname }
       ::= { rbridgeMultiFibTable 1 }

   RbridgeMultiFibEntry ::=
       SEQUENCE {
           rbridgeMultiFibNickname
               RbridgeNickname,
           rbridgeMultiFibPorts
               PortList
       }

   rbridgeMultiFibNickname OBJECT-TYPE
       SYNTAX      RbridgeNickname
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "The nickname of the multicast distribution tree."
       ::= { rbridgeMultiFibEntry 1 }

   rbridgeMultiFibPorts OBJECT-TYPE
       SYNTAX      PortList
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The list of ports to which a frame destined to this
           multicast distribution tree is flooded.  This may be pruned
           further based on other forwarding information."
       ::= { rbridgeMultiFibEntry 2 }
















Rijhsinghani & Zebrose       Standards Track                   [Page 28]

RFC 6850                RBridges: TRILL Base MIB            January 2013


   -- ---------------------------------------------------------- --
   -- The RBridge VLAN Table
   -- ---------------------------------------------------------- --

   rbridgeVlanTable  OBJECT-TYPE
       SYNTAX      SEQUENCE OF RbridgeVlanEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "A table that contains information about VLANs on the
           RBridge."
       ::= { rbridgeVlan 1 }

   rbridgeVlanEntry OBJECT-TYPE
       SYNTAX      RbridgeVlanEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "A list of information about VLANs on the RBridge."
       INDEX   { rbridgeVlanIndex }
       ::= { rbridgeVlanTable 1 }

   RbridgeVlanEntry ::=
       SEQUENCE {
           rbridgeVlanIndex
               Unsigned32,
           rbridgeVlanForwarderLosts
               Counter32,
           rbridgeVlanDisableLearning
               TruthValue,
           rbridgeVlanSnooping
               INTEGER
       }

   rbridgeVlanIndex OBJECT-TYPE
       SYNTAX      Unsigned32 (1..4094|4096..4294967295)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "The VLAN-ID referring to this VLAN."
       ::= { rbridgeVlanEntry 1 }

   rbridgeVlanForwarderLosts OBJECT-TYPE
       SYNTAX      Counter32
       UNITS       "times"
       MAX-ACCESS  read-only
       STATUS      current




Rijhsinghani & Zebrose       Standards Track                   [Page 29]

RFC 6850                RBridges: TRILL Base MIB            January 2013


       DESCRIPTION
           "The number of times this RBridge has lost appointed
           forwarder status for this VLAN on any of its ports.

           Discontinuities in the value of this counter can occur
           at re-initialization of the management system."
       REFERENCE
           "RFC 6325, Section 4.8.3"
       ::= { rbridgeVlanEntry 2 }

   rbridgeVlanDisableLearning OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "Disable learning of MAC addresses seen in this VLAN.
           One application of this may be to restrict learning to
           ESADI.  To disable learning, the value of this object
           should be set to 'true'.  The default is 'false'.

           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Section 4.8"
       DEFVAL      { false }
       ::= { rbridgeVlanEntry 3 }

   rbridgeVlanSnooping OBJECT-TYPE
       SYNTAX      INTEGER {
                       notSupported(1),
                       ipv4(2),
                       ipv6(3),
                       ipv4v6(4)
                   }
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "IP Multicast Snooping on this VLAN.  For RBridges
           performing both IPv4 and IPv6 IP Multicast Snooping, the
           value returned is ipv4v6(4)."
       REFERENCE
           "RFC 6325, Section 4.7"
       ::= { rbridgeVlanEntry 4 }








Rijhsinghani & Zebrose       Standards Track                   [Page 30]

RFC 6850                RBridges: TRILL Base MIB            January 2013


   -- ---------------------------------------------------------- --
   -- The RBridge VLAN Port Table
   -- ---------------------------------------------------------- --

   rbridgeVlanPortTable  OBJECT-TYPE
       SYNTAX      SEQUENCE OF RbridgeVlanPortEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "A table that contains information about VLANs on an RBridge
           port."
       ::= { rbridgeVlan 2 }

   rbridgeVlanPortEntry OBJECT-TYPE
       SYNTAX      RbridgeVlanPortEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "A list of information about VLANs on the RBridge port."
       INDEX   { rbridgeBasePort, rbridgeVlanIndex }
       ::= { rbridgeVlanPortTable 1 }

   RbridgeVlanPortEntry ::=
       SEQUENCE {
           rbridgeVlanPortInhibited
               TruthValue,
           rbridgeVlanPortForwarder
               TruthValue,
           rbridgeVlanPortAnnouncing
               TruthValue,
           rbridgeVlanPortDetectedVlanMapping
               TruthValue
       }

   rbridgeVlanPortInhibited OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "This VLAN has been inhibited by the RBridge due to
           conflicting forwarder information received from another
           RBridge, when the value of this object is 'true'."
       REFERENCE
           "RFC 6325, Section 4.2.4.3"
       ::= { rbridgeVlanPortEntry 1 }

   rbridgeVlanPortForwarder OBJECT-TYPE
       SYNTAX      TruthValue



Rijhsinghani & Zebrose       Standards Track                   [Page 31]

RFC 6850                RBridges: TRILL Base MIB            January 2013


       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "This RBridge is an appointed forwarder for this VLAN
           on this port, when the value of this object is 'true'."
       REFERENCE
           "RFC 6325, Section 4.2.4.3"
       ::= { rbridgeVlanPortEntry 2 }

   rbridgeVlanPortAnnouncing OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "TRILL-Hellos tagged with this VLAN can be sent by this
           RBridge on this port, when the value of this object
           is 'true'.

           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Section 4.4.3"
       DEFVAL      { true }
       ::= { rbridgeVlanPortEntry 3 }

   rbridgeVlanPortDetectedVlanMapping OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "VLAN mapping has been detected on the link attached
           to this port, when the value of this object is 'true'."
       REFERENCE
           "RFC 6325, Section 4.4.5"
       ::= { rbridgeVlanPortEntry 4 }


   -- ---------------------------------------------------------- --
   -- The RBridge Port Counter Table
   --
   -- These counters supplement counters in the Bridge MIB.
   --
   -- For example, total frames received by a bridge port and total
   -- frames transmitted by a bridge port are reported in the
   -- Port In Frames and Port Out Frames counters of the Bridge MIB.
   -- These total bridge frame counters include native as well as
   -- encapsulated frames.
   --



Rijhsinghani & Zebrose       Standards Track                   [Page 32]

RFC 6850                RBridges: TRILL Base MIB            January 2013


   -- As another example, frames discarded due to excessive frame
   -- size are reported in the port counter MTU Exceeded Discards
   -- in the Bridge MIB.
   -- ---------------------------------------------------------- --

   rbridgePortCounterTable  OBJECT-TYPE
       SYNTAX      SEQUENCE OF RbridgePortCounterEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "A table that contains per-port counters for this RBridge."
       ::= { rbridgeCounter 1 }

   rbridgePortCounterEntry OBJECT-TYPE
       SYNTAX      RbridgePortCounterEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "Counters for a port on this RBridge."
       INDEX   { rbridgeBasePort }
       ::= { rbridgePortCounterTable 1 }

   RbridgePortCounterEntry ::=
       SEQUENCE {
           rbridgePortRpfCheckFails
               Counter32,
           rbridgePortHopCountExceeds
               Counter32,
           rbridgePortOptionDrops
               Counter32,
           rbridgePortTrillInFrames
               Counter64,
           rbridgePortTrillOutFrames
               Counter64
       }

   rbridgePortRpfCheckFails OBJECT-TYPE
       SYNTAX      Counter32
       UNITS       "frames"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The number of times a multi-destination frame was
           dropped on this port because the Reverse Path Forwarding
           (RPF) check failed.

           Discontinuities in the value of this counter can occur
           at re-initialization of the management system, and at



Rijhsinghani & Zebrose       Standards Track                   [Page 33]

RFC 6850                RBridges: TRILL Base MIB            January 2013


           other times as indicated by the value of the
           ifCounterDiscontinuityTime object of the associated
           interface."
       REFERENCE
           "RFC 6325, Section 4.5.2"
       ::= { rbridgePortCounterEntry 1 }

   rbridgePortHopCountExceeds OBJECT-TYPE
       SYNTAX      Counter32
       UNITS       "frames"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The number of times a frame was dropped on this port
           because its hop count was zero.

           Discontinuities in the value of this counter can occur
           at re-initialization of the management system, and at
           other times as indicated by the value of the
           ifCounterDiscontinuityTime object of the associated
           interface."
       REFERENCE
           "RFC 6325, Section 3.6"
       ::= { rbridgePortCounterEntry 2 }

   rbridgePortOptionDrops OBJECT-TYPE
       SYNTAX      Counter32
       UNITS       "frames"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The number of times a frame was dropped on this port
           because it contained unsupported options.

           Discontinuities in the value of this counter can occur
           at re-initialization of the management system, and at
           other times as indicated by the value of the
           ifCounterDiscontinuityTime object of the associated
           interface."
       REFERENCE
           "RFC 6325, Section 3.5"
       ::= { rbridgePortCounterEntry 3 }

   rbridgePortTrillInFrames OBJECT-TYPE
       SYNTAX      Counter64
       UNITS       "frames"
       MAX-ACCESS  read-only
       STATUS      current



Rijhsinghani & Zebrose       Standards Track                   [Page 34]

RFC 6850                RBridges: TRILL Base MIB            January 2013


       DESCRIPTION
           "The number of TRILL-encapsulated frames that have been
           received by this port from its attached link, including
           management frames.

           Discontinuities in the value of this counter can occur
           at re-initialization of the management system, and at
           other times as indicated by the value of the
           ifCounterDiscontinuityTime object of the associated
           interface."
       REFERENCE
           "RFC 6325, Section 2.3"
       ::= { rbridgePortCounterEntry 4 }

   rbridgePortTrillOutFrames OBJECT-TYPE
       SYNTAX      Counter64
       UNITS       "frames"
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The number of TRILL-encapsulated frames that have been
           transmitted by this port to its attached link, including
           management frames.

           Discontinuities in the value of this counter can occur
           at re-initialization of the management system, and at
           other times as indicated by the value of the
           ifCounterDiscontinuityTime object of the associated
           interface."
       REFERENCE
           "RFC 6325, Section 2.3"
       ::= { rbridgePortCounterEntry 5 }

   -- ---------------------------------------------------------- --
   -- The RBridge VLAN ESADI Table
   -- ---------------------------------------------------------- --

   rbridgeEsadiTable  OBJECT-TYPE
       SYNTAX      SEQUENCE OF RbridgeEsadiEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "A table that contains information about ESADI instances on
           VLANs, if available."
       REFERENCE
           "RFC 6325, Section 4.2.5"
       ::= { rbridgeEsadi 1 }




Rijhsinghani & Zebrose       Standards Track                   [Page 35]

RFC 6850                RBridges: TRILL Base MIB            January 2013


   rbridgeEsadiEntry OBJECT-TYPE
       SYNTAX      RbridgeEsadiEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "Information about an ESADI instance on a VLAN."
       INDEX   { rbridgeVlanIndex }
       ::= { rbridgeEsadiTable 1 }

   RbridgeEsadiEntry ::=
       SEQUENCE {
           rbridgeEsadiEnable
               TruthValue,
           rbridgeEsadiConfidence
               Unsigned32,
           rbridgeEsadiDrbPriority
               Unsigned32,
           rbridgeEsadiDrb
               RbridgeAddress,
           rbridgeEsadiDrbHoldingTime
               Unsigned32,
           rbridgeEsadiRowStatus
               RowStatus
       }

   rbridgeEsadiEnable OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "If the RBridge is participating in an ESADI instance for
           this VLAN, the value of this object is 'true'.  To disable
           participation, set it to 'false'.

           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Section 4.2.5"
       DEFVAL      { true }
       ::= { rbridgeEsadiEntry 1 }

   rbridgeEsadiConfidence OBJECT-TYPE
       SYNTAX      Unsigned32 (0..255)
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "Confidence level of address entries sent by this
           ESADI instance.  The default is 16.



Rijhsinghani & Zebrose       Standards Track                   [Page 36]

RFC 6850                RBridges: TRILL Base MIB            January 2013


           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Section 4.2.5"
       DEFVAL      { 16 }
       ::= { rbridgeEsadiEntry 2 }

   rbridgeEsadiDrbPriority OBJECT-TYPE
       SYNTAX      Unsigned32 (0..127)
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The priority of this RBridge for being selected as the
           DRB for this ESADI instance.

           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Section 4.2.5"
       ::= { rbridgeEsadiEntry 3 }

   rbridgeEsadiDrb OBJECT-TYPE
       SYNTAX      RbridgeAddress
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The DRB on this ESADI instance's virtual link."
       REFERENCE
           "RFC 6325, Section 4.2.5"
       ::= { rbridgeEsadiEntry 4 }

   rbridgeEsadiDrbHoldingTime OBJECT-TYPE
       SYNTAX      Unsigned32 (0..127)
       MAX-ACCESS  read-create
       STATUS      current
       DESCRIPTION
           "The holding time for this ESADI instance.

           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Section 4.2.5"
       ::= { rbridgeEsadiEntry 5 }

   rbridgeEsadiRowStatus OBJECT-TYPE
       SYNTAX      RowStatus
       MAX-ACCESS  read-create
       STATUS      current



Rijhsinghani & Zebrose       Standards Track                   [Page 37]

RFC 6850                RBridges: TRILL Base MIB            January 2013


       DESCRIPTION
           "This object indicates the status of the entry."
       ::= { rbridgeEsadiEntry 6 }


   -- ---------------------------------------------------------- --
   -- The RBridge IP Multicast Snooping Port Table
   -- ---------------------------------------------------------- --

   rbridgeSnoopingPortTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF RbridgeSnoopingPortEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "For RBridges implementing IP Multicast Snooping,
           information about ports on which the presence of IPv4
           or IPv6 multicast routers has been detected."
       REFERENCE
           "RFC 6325, Section 4.7"
       ::= { rbridgeSnooping 1 }

   rbridgeSnoopingPortEntry OBJECT-TYPE
       SYNTAX      RbridgeSnoopingPortEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "Information about ports on which the presence of IPv4
           or IPv6 multicast routers has been detected for a
           VLAN."
       INDEX   { rbridgeBasePort, rbridgeVlanIndex }
       ::= { rbridgeSnoopingPortTable 1 }

   RbridgeSnoopingPortEntry ::=
       SEQUENCE {
           rbridgeSnoopingPortAddrType
               INTEGER
       }

   rbridgeSnoopingPortAddrType OBJECT-TYPE
       SYNTAX      INTEGER {
                       ipv4(1),
                       ipv6(2),
                       ipv4v6(3)
                   }
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The IP address type of an IP multicast router detected



Rijhsinghani & Zebrose       Standards Track                   [Page 38]

RFC 6850                RBridges: TRILL Base MIB            January 2013


           on this port and VLAN.  If only IPv4 router(s)
           are detected, the value returned is 'ipv4'.  If only
           IPv6 routers are detected, the value returned is
           'ipv6'.  If both IPv4 and IPv6 routers are detected on
           this port and VLAN, the value returned is 'ipv4v6'."
       REFERENCE
           "RFC 6325, Section 4.7"
       ::= { rbridgeSnoopingPortEntry 1 }

   -- ---------------------------------------------------------- --
   -- The RBridge IP Multicast Snooping Address Table
   -- ---------------------------------------------------------- --

   rbridgeSnoopingAddrTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF RbridgeSnoopingAddrEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "For RBridges implementing IP Multicast Snooping,
           information about IP multicast addresses being
           snooped."
       REFERENCE
           "RFC 6325, Section 4.8"
       ::= { rbridgeSnooping 2 }

   rbridgeSnoopingAddrEntry OBJECT-TYPE
       SYNTAX      RbridgeSnoopingAddrEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "Information about IP multicast addresses being
           snooped."
       INDEX  { rbridgeVlanIndex, rbridgeSnoopingAddrType,
                rbridgeSnoopingAddr }
       ::= { rbridgeSnoopingAddrTable 1 }

   RbridgeSnoopingAddrEntry ::=
       SEQUENCE {
           rbridgeSnoopingAddrType
               InetAddressType,
           rbridgeSnoopingAddr
               InetAddress,
           rbridgeSnoopingAddrPorts
               PortList
       }

   rbridgeSnoopingAddrType OBJECT-TYPE
       SYNTAX      InetAddressType



Rijhsinghani & Zebrose       Standards Track                   [Page 39]

RFC 6850                RBridges: TRILL Base MIB            January 2013


       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "The IP multicast address type for which a listener has been
           detected by this RBridge.  This MIB requires support for only
           IPv4 and IPv6 address types."
       REFERENCE
           "RFC 6325, Section 4.7"
       ::= { rbridgeSnoopingAddrEntry 1 }

   rbridgeSnoopingAddr OBJECT-TYPE
       SYNTAX      InetAddress
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "The IP multicast address for which a listener has been
           detected by this RBridge.  The address type of this object
           is specified in rbridgeSnoopingAddrType.  This MIB requires
           support for only global IPv4 and IPv6 addresses, so the
           length of the object can be either 4 or 16 bytes.  Hence,
           the index will not exceed the OID size limit."
       REFERENCE
           "RFC 6325, Section 4.7"
       ::= { rbridgeSnoopingAddrEntry 2 }

   rbridgeSnoopingAddrPorts OBJECT-TYPE
       SYNTAX      PortList
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The set of ports on which a listener has been detected
           for this IP multicast address."
       REFERENCE
           "RFC 6325, Section 4.7"
       ::= { rbridgeSnoopingAddrEntry 3 }


   -- ---------------------------------------------------------- --
   -- Distribution Trees
   -- ---------------------------------------------------------- --

   rbridgeDtreePriority OBJECT-TYPE

       SYNTAX      Unsigned32 (1..65535)
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "The distribution tree root priority for this RBridge.



Rijhsinghani & Zebrose       Standards Track                   [Page 40]

RFC 6850                RBridges: TRILL Base MIB            January 2013


           The default value of this object is 32768.

           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Section 4.5"
       ::= { rbridgeDtree 1 }

   rbridgeDtreeActiveTrees OBJECT-TYPE
       SYNTAX      Unsigned32
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The total number of trees being computed by all RBridges
           in the campus."
       REFERENCE
           "RFC 6325, Section 4.5"
       ::= { rbridgeDtree 2 }

   rbridgeDtreeMaxTrees OBJECT-TYPE
       SYNTAX      Unsigned32
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The maximum number of trees this RBridge can compute."
       REFERENCE
           "RFC 6325, Section 4.5"
       ::= { rbridgeDtree 3 }

   rbridgeDtreeDesiredUseTrees OBJECT-TYPE
       SYNTAX      Unsigned32
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The maximum number of trees this RBridge would like to
           use for transmission of ingress multi-destination frames."
       REFERENCE
           "RFC 6325, Section 4.5"
       ::= { rbridgeDtree 4 }

   rbridgeDtreeTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF RbridgeDtreeEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "Information about distribution trees being computed
           by this RBridge."




Rijhsinghani & Zebrose       Standards Track                   [Page 41]

RFC 6850                RBridges: TRILL Base MIB            January 2013


       REFERENCE
           "RFC 6325, Section 4.5"
       ::= { rbridgeDtree 5 }

   rbridgeDtreeEntry OBJECT-TYPE
       SYNTAX      RbridgeDtreeEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "List of information about distribution trees being computed
           by this RBridge."
       INDEX  { rbridgeDtreeNumber }
       ::= { rbridgeDtreeTable 1 }

   RbridgeDtreeEntry ::=
       SEQUENCE {
           rbridgeDtreeNumber
               Unsigned32,
           rbridgeDtreeNickname
               RbridgeNickname,
           rbridgeDtreeIngress
               TruthValue
       }

   rbridgeDtreeNumber OBJECT-TYPE
       SYNTAX      Unsigned32 (0..65535)
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "The tree number of a distribution tree being computed by
           this RBridge."
       REFERENCE
           "RFC 6325, Section 4.5"
       ::= { rbridgeDtreeEntry 1 }

   rbridgeDtreeNickname OBJECT-TYPE
       SYNTAX      RbridgeNickname
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The nickname of the distribution tree."
       REFERENCE
           "RFC 6325, Section 4.5"
       ::= { rbridgeDtreeEntry 2 }

   rbridgeDtreeIngress OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-only



Rijhsinghani & Zebrose       Standards Track                   [Page 42]

RFC 6850                RBridges: TRILL Base MIB            January 2013


       STATUS      current
       DESCRIPTION
           "Indicates whether this RBridge might choose this
           distribution tree to ingress a multi-destination frame."
       REFERENCE
           "RFC 6325, Section 4.5"
       ::= { rbridgeDtreeEntry 3 }


   -- ---------------------------------------------------------- --
   -- TRILL Neighbor List
   -- ---------------------------------------------------------- --

   rbridgeTrillMinMtuDesired OBJECT-TYPE
       SYNTAX      Unsigned32
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "The desired minimum acceptable inter-RBridge link MTU for
           the campus, that is, originatingLSPBufferSize.

           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Section 4.3"
       ::= { rbridgeTrill 1 }

   rbridgeTrillSz OBJECT-TYPE
       SYNTAX      Unsigned32
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "The minimum acceptable inter-RBridge link size for the
           campus for the proper operation of TRILL IS-IS."
       REFERENCE
           "RFC 6325, Section 4.3"
       ::= { rbridgeTrill 2 }

   rbridgeTrillMaxMtuProbes OBJECT-TYPE
       SYNTAX      Unsigned32 (1..255)
       MAX-ACCESS  read-write
       STATUS      current
       DESCRIPTION
           "The number of failed MTU-probes before the RBridge
           concludes that a particular MTU is not supported by
           a neighbor.





Rijhsinghani & Zebrose       Standards Track                   [Page 43]

RFC 6850                RBridges: TRILL Base MIB            January 2013


           The value of this object MUST be retained across
           re-initializations of the management system."
       REFERENCE
           "RFC 6325, Section 4.3"
       ::= { rbridgeTrill 3 }

   rbridgeTrillNbrTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF RbridgeTrillNbrEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "Information about this RBridge's TRILL neighbors."
       REFERENCE
           "RFC 6325, Section 4.4.2.1"
       ::= { rbridgeTrill 4 }

   rbridgeTrillNbrEntry OBJECT-TYPE
       SYNTAX      RbridgeTrillNbrEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "List of information about this RBridge's TRILL neighbors."
       INDEX  { rbridgeTrillNbrMacAddr }
       ::= { rbridgeTrillNbrTable 1 }

   RbridgeTrillNbrEntry ::=
       SEQUENCE {
           rbridgeTrillNbrMacAddr
               MacAddress,
           rbridgeTrillNbrMtu
               Unsigned32,
           rbridgeTrillNbrFailedMtuTest
               TruthValue
       }

   rbridgeTrillNbrMacAddr OBJECT-TYPE
       SYNTAX      MacAddress
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
           "The MAC address of a neighbor of this RBridge."
       REFERENCE
           "RFC 6325, Section 4.4.2.1"
       ::= { rbridgeTrillNbrEntry 1 }

   rbridgeTrillNbrMtu OBJECT-TYPE
       SYNTAX      Unsigned32
       MAX-ACCESS  read-only



Rijhsinghani & Zebrose       Standards Track                   [Page 44]

RFC 6850                RBridges: TRILL Base MIB            January 2013


       STATUS      current
       DESCRIPTION
           "MTU size for this neighbor for IS-IS communication
           purposes."
       REFERENCE
           "RFC 6325, Section 4.3.2"
       ::= { rbridgeTrillNbrEntry 2 }

   rbridgeTrillNbrFailedMtuTest OBJECT-TYPE
       SYNTAX      TruthValue
       MAX-ACCESS  read-only
       STATUS      current
       DESCRIPTION
           "If true, indicates that the neighbor's tested MTU is less
           than the minimum acceptable inter-bridge link MTU for the
           campus (1470)."
       REFERENCE
           "RFC 6325, Section 4.3.1"
       ::= { rbridgeTrillNbrEntry 3 }


   -- ---------------------------------------------------------- --
   -- Notifications for use by RBridges
   -- ---------------------------------------------------------- --

   rbridgeBaseNewDrb NOTIFICATION-TYPE
       -- OBJECTS     { }
       STATUS      current
       DESCRIPTION
           "The rbridgeBaseNewDrb notification indicates that the
           sending agent has become the new Designated RBridge; the
           notification is sent by an RBridge soon after its election
           as the new DRB root, e.g., upon expiration of the Topology
           Change Timer, immediately subsequent to its election."
       ::= { rbridgeNotifications 1 }

   rbridgeBaseTopologyChange NOTIFICATION-TYPE
       -- OBJECTS     { }
       STATUS      current
       DESCRIPTION
           "The rbridgeBaseTopologyChange notification is sent by an
           RBridge when any of its configured ports transition to/from
           the VLAN-x designated forwarder.  The notification is not
           sent if an rbridgeBaseNewDrb notification is sent for the
           same transition."
       ::= { rbridgeNotifications 2 }





Rijhsinghani & Zebrose       Standards Track                   [Page 45]

RFC 6850                RBridges: TRILL Base MIB            January 2013


   -- Compliance and Group sections

   rbridgeCompliances    OBJECT IDENTIFIER ::= { rbridgeConformance 1 }

   rbridgeGroup          OBJECT IDENTIFIER ::= { rbridgeConformance 2 }


   -- ---------------------------------------------------------- --
   -- Units of Conformance
   -- ---------------------------------------------------------- --

   rbridgeBaseGroup OBJECT-GROUP
       OBJECTS {
           rbridgeBaseTrillVersion,
           rbridgeBaseNumPorts,
           rbridgeBaseForwardDelay,
           rbridgeBaseUniMultipathEnable,
           rbridgeBaseMultiMultipathEnable,
           rbridgeBaseAcceptEncapNonadj,
           rbridgeBaseNicknameNumber
       }
       STATUS      current
       DESCRIPTION
           "A collection of objects providing basic control
           and status information for the RBridge."
       ::= { rbridgeGroup 1 }

   rbridgeBaseNicknameGroup OBJECT-GROUP
       OBJECTS {
           rbridgeBaseNicknamePriority,
           rbridgeBaseNicknameDtrPriority,
           rbridgeBaseNicknameType,
           rbridgeBaseNicknameRowStatus
       }
       STATUS      current
       DESCRIPTION
           "A collection of objects providing basic control
           and status information for RBridge nicknames."
       ::= { rbridgeGroup 2 }

   rbridgeBasePortGroup OBJECT-GROUP
       OBJECTS {
           rbridgeBasePortIfIndex,
           rbridgeBasePortDisable,
           rbridgeBasePortTrunkPort,
           rbridgeBasePortAccessPort,
           rbridgeBasePortP2pHellos,
           rbridgeBasePortState,



Rijhsinghani & Zebrose       Standards Track                   [Page 46]

RFC 6850                RBridges: TRILL Base MIB            January 2013


           rbridgeBasePortDesiredDesigVlan,
           rbridgeBasePortDesigVlan,
           rbridgeBasePortInhibitionTime,
           rbridgeBasePortDisableLearning,
           rbridgeBasePortStpRoot,
           rbridgeBasePortStpRootChanges,
           rbridgeBasePortStpWiringCloset
       }
       STATUS      current
       DESCRIPTION
           "A collection of objects providing basic control
           and status information for RBridge ports."
       ::= { rbridgeGroup 3 }

   rbridgeFdbGroup OBJECT-GROUP
       OBJECTS {
           rbridgeConfidenceNative,
           rbridgeConfidenceDecap,
           rbridgeConfidenceStatic,
           rbridgeUniFdbPort,
           rbridgeUniFdbNickname,
           rbridgeUniFdbConfidence,
           rbridgeUniFdbStatus
       }
       STATUS      current
       DESCRIPTION
           "A collection of objects providing information
           about the Unicast Address Database."
       ::= { rbridgeGroup 4 }

   rbridgeFibGroup OBJECT-GROUP
       OBJECTS {
           rbridgeUniFibHopCount,
           rbridgeMultiFibPorts
       }
       STATUS      current
       DESCRIPTION
           "A collection of objects providing information
           about the Unicast and Multicast FIBs."
       ::= { rbridgeGroup 5 }

   rbridgeVlanGroup OBJECT-GROUP
       OBJECTS {
           rbridgeVlanForwarderLosts,
           rbridgeVlanDisableLearning,
           rbridgeVlanSnooping,
           rbridgeVlanPortInhibited,
           rbridgeVlanPortForwarder,



Rijhsinghani & Zebrose       Standards Track                   [Page 47]

RFC 6850                RBridges: TRILL Base MIB            January 2013


           rbridgeVlanPortAnnouncing,
           rbridgeVlanPortDetectedVlanMapping
       }
       STATUS      current
       DESCRIPTION
           "A collection of objects providing information
           about VLANs on the RBridge."
       ::= { rbridgeGroup 6 }

   rbridgePortCounterGroup OBJECT-GROUP
       OBJECTS {
           rbridgePortRpfCheckFails,
           rbridgePortHopCountExceeds,
           rbridgePortOptionDrops,
           rbridgePortTrillInFrames,
           rbridgePortTrillOutFrames
       }
       STATUS      current
       DESCRIPTION
           "A collection of objects providing per-port
           counters for the RBridge."
       ::= { rbridgeGroup 7 }

   rbridgeEsadiGroup OBJECT-GROUP
       OBJECTS {
           rbridgeEsadiEnable,
           rbridgeEsadiConfidence,
           rbridgeEsadiDrbPriority,
           rbridgeEsadiDrb,
           rbridgeEsadiDrbHoldingTime,
           rbridgeEsadiRowStatus
       }
       STATUS      current
       DESCRIPTION
           "A collection of objects providing information
           about ESADI instances on the RBridge."
       ::= { rbridgeGroup 8 }

   rbridgeSnoopingGroup OBJECT-GROUP
       OBJECTS {
           rbridgeSnoopingPortAddrType,
           rbridgeSnoopingAddrPorts
       }
       STATUS      current
       DESCRIPTION
           "A collection of objects providing information about
           IP Multicast Snooping.  This MIB requires support for
           only global IPv4 and IPv6 address types in



Rijhsinghani & Zebrose       Standards Track                   [Page 48]

RFC 6850                RBridges: TRILL Base MIB            January 2013


           rbridgeSnoopingPortAddrType and rbridgeSnoopingAddrType,
           so the length of rbridgeSnoopingAddr can be either 4 or
           16 bytes."
       ::= { rbridgeGroup 9 }

   rbridgeDtreeGroup OBJECT-GROUP
       OBJECTS {
           rbridgeDtreePriority,
           rbridgeDtreeActiveTrees,
           rbridgeDtreeMaxTrees,
           rbridgeDtreeDesiredUseTrees,
           rbridgeDtreeNickname,
           rbridgeDtreeIngress
       }
       STATUS      current
       DESCRIPTION
           "A collection of objects providing information
           about distribution trees."
       ::= { rbridgeGroup 10 }

   rbridgeTrillGroup OBJECT-GROUP
       OBJECTS {
           rbridgeTrillMinMtuDesired,
           rbridgeTrillSz,
           rbridgeTrillMaxMtuProbes,
           rbridgeTrillNbrMtu,
           rbridgeTrillNbrFailedMtuTest
       }
       STATUS      current
       DESCRIPTION
           "A collection of objects providing information
           about TRILL neighbors."
       ::= { rbridgeGroup 11 }

   rbridgeNotificationGroup NOTIFICATION-GROUP
       NOTIFICATIONS {
           rbridgeBaseNewDrb,
           rbridgeBaseTopologyChange
       }
       STATUS      current
       DESCRIPTION
           "A collection of objects describing notifications (traps)."
       ::= { rbridgeGroup 12 }








Rijhsinghani & Zebrose       Standards Track                   [Page 49]

RFC 6850                RBridges: TRILL Base MIB            January 2013


   -- ---------------------------------------------------------- --
   -- Compliance Statement
   -- ---------------------------------------------------------- --

   rbridgeCompliance MODULE-COMPLIANCE
          STATUS      current
          DESCRIPTION
              "The compliance statement for support of RBridge
              services."

          MODULE
              MANDATORY-GROUPS {
                  rbridgeBaseGroup,
                  rbridgeBaseNicknameGroup,
                  rbridgeBasePortGroup,
                  rbridgeFdbGroup,
                  rbridgeFibGroup,
                  rbridgeVlanGroup,
                  rbridgeDtreeGroup,
                  rbridgeTrillGroup,
                  rbridgeNotificationGroup
              }

          GROUP   rbridgePortCounterGroup
          DESCRIPTION
              "Implementation of this group is optional."

          GROUP   rbridgeEsadiGroup
          DESCRIPTION
              "Implementation of this group is optional."

          GROUP   rbridgeSnoopingGroup
          DESCRIPTION
              "Implementation of this group is optional."

          ::= { rbridgeCompliances 1 }

   rbridgeReadOnlyCompliance MODULE-COMPLIANCE
          STATUS      current
          DESCRIPTION
              "When this MIB is implemented in read-only mode, then
              the implementation can claim read-only compliance.
              In that case, RBridge objects can be monitored but
              cannot be configured with this implementation."







Rijhsinghani & Zebrose       Standards Track                   [Page 50]

RFC 6850                RBridges: TRILL Base MIB            January 2013


          MODULE
              MANDATORY-GROUPS {
                  rbridgeBaseGroup,
                  rbridgeBaseNicknameGroup,
                  rbridgeBasePortGroup,
                  rbridgeFdbGroup,
                  rbridgeFibGroup,
                  rbridgeVlanGroup,
                  rbridgeDtreeGroup,
                  rbridgeTrillGroup,
                  rbridgeNotificationGroup
              }

          OBJECT  rbridgeBaseForwardDelay
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeBaseUniMultipathEnable
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeBaseMultiMultipathEnable
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeBaseAcceptEncapNonadj
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeBaseNicknameNumber
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeBaseNicknamePriority
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeBaseNicknameDtrPriority
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."




Rijhsinghani & Zebrose       Standards Track                   [Page 51]

RFC 6850                RBridges: TRILL Base MIB            January 2013


          OBJECT  rbridgeBaseNicknameRowStatus
          SYNTAX  INTEGER { active(1) }
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required, and 'active' is the only
              status that needs to be supported."

          OBJECT  rbridgeBasePortDisable
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeBasePortTrunkPort
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeBasePortAccessPort
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeBasePortP2pHellos
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeBasePortInhibitionTime
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeBasePortDisableLearning
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeBasePortDesiredDesigVlan
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeBasePortStpWiringCloset
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."





Rijhsinghani & Zebrose       Standards Track                   [Page 52]

RFC 6850                RBridges: TRILL Base MIB            January 2013


          OBJECT  rbridgeConfidenceNative
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeConfidenceDecap
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeConfidenceStatic
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeVlanDisableLearning
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeVlanPortAnnouncing
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeEsadiEnable
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeEsadiConfidence
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeEsadiDrbPriority
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeEsadiDrbHoldingTime
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeEsadiRowStatus
          SYNTAX  INTEGER { active(1) }
          MIN-ACCESS  read-only



Rijhsinghani & Zebrose       Standards Track                   [Page 53]

RFC 6850                RBridges: TRILL Base MIB            January 2013


          DESCRIPTION
              "Write access is not required, and 'active' is the only
              status that needs to be supported."

          OBJECT  rbridgeDtreePriority
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeTrillMinMtuDesired
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          OBJECT  rbridgeTrillMaxMtuProbes
          MIN-ACCESS  read-only
          DESCRIPTION
              "Write access is not required."

          GROUP   rbridgePortCounterGroup
          DESCRIPTION
              "Implementation of this group is optional."

          GROUP   rbridgeEsadiGroup
          DESCRIPTION
              "Implementation of this group is optional."

          GROUP   rbridgeSnoopingGroup
          DESCRIPTION
              "Implementation of this group is optional."

          ::= { rbridgeCompliances 2 }

      END

















Rijhsinghani & Zebrose       Standards Track                   [Page 54]

RFC 6850                RBridges: TRILL Base MIB            January 2013


8.  Security Considerations

   This MIB relates to a system that will provide network connectivity
   and packet-forwarding services.  As such, improper manipulation of
   the objects represented by this MIB may result in denial of service
   to a large number of end-users.

   There are a number of management objects defined in this MIB module
   with a MAX-ACCESS clause of read-write and/or read-create.  Such
   objects may be considered sensitive or vulnerable in some network
   environments.  The support for SET operations in a non-secure
   environment without proper protection can have a negative effect on
   network operations.  These are the tables and objects and their
   sensitivity/vulnerability:

   The following tables and objects in the RBRIDGE-MIB can be
   manipulated to interfere with the operation of RBridges:

   o  rbridgeBaseUniMultipathEnable affects the ability of the RBridge
      to route unicast traffic over multiple paths, and
      rbridgeBaseMultiMultipathEnable affects the ability of the RBridge
      to route multi-destination traffic over multiple paths.

   o  rbridgeBasePortTable contains a number of objects that may affect
      network connectivity.  Actions that may be triggered by
      manipulating objects in this table include disabling of an RBridge
      port, discarding of native packets, disabling learning, and
      others.

   o  rbridgeEsadiTable contains objects that affect the operation of
      the ESADI protocol used for learning, and manipulation of the
      objects contained therein can be used to confuse the learning
      ability of RBridges.

   o  rbridgeDtreePriority can affect computation of distribution trees
      within an RBridge campus, thereby affecting the forwarding of
      multi-destination traffic.

   o  rbridgeTrillMinMtuDesired can affect the size of packets being
      used to exchange information between RBridges.

   Some of the readable objects in this MIB module (i.e., objects with a
   MAX-ACCESS other than not-accessible) may be considered sensitive or
   vulnerable in some network environments.  It is thus important to
   control even GET and/or NOTIFY access to these objects and possibly
   to even encrypt the values of these objects when sending them over





Rijhsinghani & Zebrose       Standards Track                   [Page 55]

RFC 6850                RBridges: TRILL Base MIB            January 2013


   the network via SNMP.  For example, access to network topology and
   RBridge attributes can reveal information that should not be
   available to all users of the network.

   SNMP versions prior to SNMPv3 did not include adequate security.
   Even if the network itself is secure (for example by using IPsec),
   there is no control as to who on the secure network is allowed to
   access and GET/SET (read/change/create/delete) the objects in this
   MIB module.

   Implementations SHOULD provide the security features described by the
   SNMPv3 framework (see [RFC3410]), and implementations claiming
   compliance to the SNMPv3 standard MUST include full support for
   authentication and privacy via the User-based Security Model (USM)
   [RFC3414] with the AES cipher algorithm [RFC3826].  Implementations
   MAY also provide support for the Transport Security Model (TSM)
   [RFC5591] in combination with a secure transport such as SSH
   [RFC5592] or TLS/DTLS [RFC6353].

   Further, deployment of SNMP versions prior to SNMPv3 is NOT
   RECOMMENDED.  Instead, it is RECOMMENDED to deploy SNMPv3 and to
   enable cryptographic security.  It is then a customer/operator
   responsibility to ensure that the SNMP entity giving access to an
   instance of this MIB module is properly configured to give access to
   the objects only to those principals (users) that have legitimate
   rights to indeed GET or SET (change/create/delete) them.

   For other RBridge security considerations, see [RFC6325].

9.  IANA Considerations

   The MIB module in this document uses the following IANA-assigned
   OBJECT IDENTIFIER value recorded in the SMI Numbers registry:

      Descriptor   OBJECT IDENTIFIER value
      ----------   -----------------------

      rbridgeMIB   { mib-2 214 }

10.  Contributors

   The authors would like to acknowledge the contributions of Donald
   Eastlake, Radia Perlman, Anoop Ghanwani, Dan Romascanu, Mahesh Akula,
   Sue Hares, and Joan Cucchiara.







Rijhsinghani & Zebrose       Standards Track                   [Page 56]

RFC 6850                RBridges: TRILL Base MIB            January 2013


11.  References

11.1.  Normative References

   [RFC2119]   Bradner, S., "Key words for use in RFCs to Indicate
               Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC2578]   McCloghrie, K., Ed., Perkins, D., Ed., and J.
               Schoenwaelder, Ed., "Structure of Management Information
               Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.

   [RFC2579]   McCloghrie, K., Ed., Perkins, D., Ed., and J.
               Schoenwaelder, Ed., "Textual Conventions for SMIv2",
               STD 58, RFC 2579, April 1999.

   [RFC2580]   McCloghrie, K., Ed., Perkins, D., Ed., and J.
               Schoenwaelder, Ed., "Conformance Statements for SMIv2",
               STD 58, RFC 2580, April 1999.

   [RFC2863]   McCloghrie, K. and F. Kastenholz, "The Interfaces Group
               MIB", RFC 2863, June 2000.

   [RFC3414]   Blumenthal, U. and B. Wijnen, "User-based Security Model
               (USM) for version 3 of the Simple Network Management
               Protocol (SNMPv3)", STD 62, RFC 3414, December 2002.

   [RFC3826]   Blumenthal, U., Maino, F., and K. McCloghrie, "The
               Advanced Encryption Standard (AES) Cipher Algorithm in
               the SNMP User-based Security Model", RFC 3826, June 2004.

   [RFC4001]   Daniele, M., Haberman, B., Routhier, S., and J.
               Schoenwaelder, "Textual Conventions for Internet Network
               Addresses", RFC 4001, February 2005.

   [RFC4188]   Norseth, K., Ed., and E. Bell, Ed., "Definitions of
               Managed Objects for Bridges", RFC 4188, September 2005.

   [RFC4363]   Levi, D. and D. Harrington, "Definitions of Managed
               Objects for Bridges with Traffic Classes, Multicast
               Filtering, and Virtual LAN Extensions", RFC 4363,
               January 2006.

   [RFC4444]   Parker, J., Ed., "Management Information Base for
               Intermediate System to Intermediate System (IS-IS)",
               RFC 4444, April 2006.






Rijhsinghani & Zebrose       Standards Track                   [Page 57]

RFC 6850                RBridges: TRILL Base MIB            January 2013


   [RFC5591]   Harrington, D. and W. Hardaker, "Transport Security Model
               for the Simple Network Management Protocol (SNMP)",
               RFC 5591, June 2009.

   [RFC5592]   Harrington, D., Salowey, J., and W. Hardaker, "Secure
               Shell Transport Model for the Simple Network Management
               Protocol (SNMP)", RFC 5592, June 2009.

   [RFC6325]   Perlman, R., Eastlake 3rd, D., Dutt, D., Gai, S., and A.
               Ghanwani, "Routing Bridges (RBridges): Base Protocol
               Specification", RFC 6325, July 2011.

   [RFC6353]   Hardaker, W., "Transport Layer Security (TLS) Transport
               Model for the Simple Network Management Protocol (SNMP)",
               RFC 6353, July 2011.

11.2.  Informative References

   [RFC3410]   Case, J., Mundy, R., Partain, D., and B. Stewart,
               "Introduction and Applicability Statements for Internet-
               Standard Management Framework", RFC 3410, December 2002.

   [RFC4663]   Harrington, D., "Transferring MIB Work from IETF Bridge
               MIB WG to IEEE 802.1 WG", RFC 4663, September 2006.

   [RFC5556]   Touch, J. and R. Perlman, "Transparent Interconnection of
               Lots of Links (TRILL): Problem and Applicability
               Statement", RFC 5556, May 2009.























Rijhsinghani & Zebrose       Standards Track                   [Page 58]

RFC 6850                RBridges: TRILL Base MIB            January 2013


Authors' Addresses

   Anil Rijhsinghani
   Hewlett-Packard
   153 Taylor St.
   Littleton, MA
   USA

   Phone: +1 508 323 1251
   EMail: anil@charter.net


   Kate Zebrose
   HW Embedded
   26 Josephine Ave.
   Somerville, MA
   USA

   Phone: +1 617 840 9673
   EMail: zebrose@alum.mit.edu































Rijhsinghani & Zebrose       Standards Track                   [Page 59]